Auto Glass Tools

20 - 40% off!

Find us on Facebook

s

Give us a call for the lowest price on Equalizer Tools!

Equalizer Express Blades

Equalizer Express Blades

Here you will find all of your Equalizer Express blades.

25 Item(s)

per page

List  Grid 

Set Descending Direction
  1. Equalizer Express Blade Handle

    Equalizer Express Blade Handle

    Regular Price: $19.00

    Special Price $14.48

    Now you can use any Equalizer Express blade as a long knife just by sliding it into one of our Express Blade Handles. The handle is made of aluminum and is a full 8-1/2" long (perfect for two handed operation). The blade can be set into the handle at any depth from 3/4" up to 3-3/4" just by tightening the steel screw into the blade when you have set the blade at the desired depth. Blade not included. Learn More
  2. Bullet™ Blade 3x10 REB262
  3. Equalizer HydroBlade

    Equalizer HydroBlade - EHB145

    $31.90

    Equalizer HydroBlades have a series of small dimples stamped on the side of the blade that rides against the urethane. These dimples are designed to carry cutting lubricant into the urethane that is being cut by the blade. With each stroke the blade picks up cutting lubricant on the outside of the urethane and deposits it inside the urethane allowing for each additional stroke of the blade to slide easily through the urethane. Besides making the blade cut easier they also save battery life and reduce vibration because of the reduced friction on the blade. Made of a proprietary grade of stainless steel. Made in the USA. Learn More
  4. Express Blades - 1-1/2" Wide, 12" Long

    Express Blade, 1-1/2 x 12 - LBE1403

    $31.90

    Express Blade, 1-1/2 x 12 Learn More
  5. BFE1400 3x10 Express Blade

    Express Blade, 3 x 10 - BFE1400

    $31.90

    The Equalizer Express Blades were developed from daily use on hundreds of different vehicles. The BFE1400 is the most used size and is perfect for slicing through wide bands of urethane. It works well in all places where you plunge cut or angle cut. The BFE1401 blade is perfect for removing glass that is not broken. Its narrow width is more flexible, which puts less stress on the glass. The LBE1402 work well where the urethane is far below the glass, but there is a limited amount of vertical space inside the vehicle. The LBE1403 blade is perfect for removing glass that is not broken. Its narrow width is more flexible, which puts less stress on the glass. The RLE1404 work well where the urethane is very deep below the dash. These blades can also be used with our Express Blade Handle. Made of a proprietary grade of stainless steel. Made in the USA. Learn More
  6. Bullet™ Blade - 1-1/2x12

    Bullet™ Blade - 1-1/2x12

    $31.90

    1-1/2” W x 12” L Learn More
  7. Equalizer Standard Hydroblade - 3" Wide 10" Long (EHB186)

    Equalizer Standard Hydroblade - 3" Wide 10" Long - EHB186

    $31.90

    Equalizer HydroBlades are designed to carry cutting lubricant into the urethane that is being cut by the blade. Learn More
  8. Equalizer HydroBlade

    Equalizer HydroBlade - EHL146

    $31.90

    Equalizer HydroBlades have a series of small dimples stamped on the side of the blade that rides against the urethane. These dimples are designed to carry cutting lubricant into the urethane that is being cut by the blade. With each stroke the blade picks up cutting lubricant on the outside of the urethane and deposits it inside the urethane allowing for each additional stroke of the blade to slide easily through the urethane. Besides making the blade cut easier they also save battery life and reduce vibration because of the reduced friction on the blade. Made of a proprietary grade of stainless steel. Made in the USA. Learn More
  9. Bullet™ Blade • 3x12 REL263
  10. Equalizer Standard Hydroblade - 3" Wide 12" Long (EHL187)

    Equalizer Standard Hydroblade - 3" Wide 12" Long - EHL187

    $31.90

    Equalizer HydroBlades are designed to carry cutting lubricant into the urethane that is being cut by the blade. With each stroke the blade picks up cutting lubricant on the outside of the urethane and deposits it inside the urethane. Learn More
  11. LBE1402 3x12 Express Blade

    Express Blade, 3 x 12 - LBE1402

    $31.90

    The Equalizer Express Blades were developed from daily use on hundreds of different vehicles. The BFE1400 is the most used size and is perfect for slicing through wide bands of urethane. It works well in all places where you plunge cut or angle cut. The BFE1401 blade is perfect for removing glass that is not broken. Its narrow width is more flexible, which puts less stress on the glass. The LBE1402 work well where the urethane is far below the glass, but there is a limited amount of vertical space inside the vehicle. The LBE1403 blade is perfect for removing glass that is not broken. Its narrow width is more flexible, which puts less stress on the glass. The RLE1404 work well where the urethane is very deep below the dash. These blades can also be used with our Express Blade Handle. Made of a proprietary grade of stainless steel. Made in the USA. Learn More
  12. Express Hydroblade 3" Wide 10" Long

    Equalizer HydroBlade - EHB186

    $31.90

    Equalizer HydroBlades are designed to carry cutting lubricant into the urethane that is being cut by the blade. With each stroke the blade picks up cutting lubricant on the outside of the urethane and deposits it inside the urethane. Learn More
  13. Equalizer Quarter Glass & Corner HydroBlade (Drivers Side) HQS177

    Equalizer HydroBlade - HQS177

    $33.90

    Now Serrated For An Even Better Cut! Many quarter glasses come to a sharp point in the back and can be difficult to remove. These blades are designed to reach into those difficult areas and cut the urethane. They are also very useful on those vehicles that have corners with sharp angles. It can be very challenging to reach into some of those corners to cut the urethane. The blades are very flexible to allow the tool to be held outside the quarter glass opening while cutting inside. Each blade is designed for a specific side of the vehicle. Made of a proprietary grade of stainless steel. Made in the USA. 1-3/8" Wide, 12" Long Driver Side Learn More
  14. Equalizer Express Specialty Blades  HydroBlade  10" Long (EHF173)

    Equalizer HydroBlade - EHF173

    $33.90

    Some areas require side-to-side cutting. This is more common around very radical curves in the glass, and in vehicles that have corners with a sharper-than-90 angle. It can be difficult to get all the way up into these corners with a square-endblade, but with the round tip it will reach up into the corner and cut the urethane. This blades can also be used with our Express Blade Handle. Made of a proprietary grade of stainless steel. Made in the USA. Learn More
  15. Equalizer Wide Quarter Glass & Corner HydroBlade (Drivers Side HQW179)

    Equalizer HydroBlade - HQW179

    $33.90

    Now Serrated For An Even Better Cut! 2" Wide, 12" Long Driver Side These blades are the same as our HQS176 and HQS177, but are wider to accommodate the quarter glasses and corners that are not as pointed. The blades are very flexible to allow the tool to be held outside the quarter glass opening while cutting inside. Each blade is designed for a specific side of the vehicle. Made of a proprietary grade of stainless steel. Made in the USA. Learn More
  16. Equalizer Quarter Glass & Corner HydroBlade (Passenger Side) HQS176

    Equalizer HydroBlade - HQS176

    $33.90

    Now Serrated For An Even Better Cut! Many quarter glasses come to a sharp point in the back and can be difficult to remove. These blades are designed to reach into those difficult areas and cut the urethane. They are also very useful on those vehicles that have corners with sharp angles. It can be very challenging to reach into some of those corners to cut the urethane. The blades are very flexible to allow the tool to be held outside the quarter glass opening while cutting inside. Each blade is designed for a specific side of the vehicle. Made of a proprietary grade of stainless steel. Made in the USA. 1-3/8" Wide, 12" Long Passenger Side Learn More
  17. Equalizer Wide Quarter Glass & Corner HydroBlade (Passenger Side HQW178)

    Equalizer HydroBlade - HQW178

    $33.90

    This is a new spin on the tried and true design of the originalHydroBlade. The Equalizer Piranha blade uses the samecutting technology as the original HydroBlade but alsoincorporates serration on a portion of each side of the blade,making cutting from left to right/right to left much easier. Made of a proprietary grade of stainless steel. Made in the USA. Learn More
  18. Express Blades - 3" Wide, 14" Long

    Express Blade, 3 x 14 - RLE1404

    $35.90

    The Equalizer Express Blades were developed from daily use on hundreds of different vehicles. The BFE1400 is the most used size and is perfect for slicing through wide bands of urethane. It works well in all places where you plunge cut or angle cut. The BFE1401 blade is perfect for removing glass that is not broken. Its narrow width is more flexible, which puts less stress on the glass. The LBE1402 work well where the urethane is far below the glass, but there is a limited amount of vertical space inside the vehicle. The LBE1403 blade is perfect for removing glass that is not broken. Its narrow width is more flexible, which puts less stress on the glass. The RLE1404 work well where the urethane is very deep below the dash. These blades can also be used with our Express Blade Handle. Made of a proprietary grade of stainless steel. Made in the USA. Learn More
  19. Bullet™ Blade 3x14 REE264
  20. Express HydroBlade 3" x 14" (EHE160)

    Equalizer HydroBlade - EHE160

    $35.90

    Equalizer HydroBlades have a series of small dimples stamped on the side of the blade that rides against the urethane. These dimples are designed to carry cutting lubricant into the urethane that is being cut by the blade. With each stroke the blade picks up cutting lubricant on the outside of the urethane and deposits it inside the urethane allowing for each additional stroke of the blade to slide easily through the urethane. Besides make the blade cut easier they also save battery life and reduce vibration because of the reduced friction on the blade. Made of a proprietary grade of stainless steel. Made in the USA. Learn More
  21. Equalizer Piranha Blade 3"x10"
  22. Equalizer HydroBlade

    Equalizer HydroBlade - EHS174

    $38.68

    ome vehicles have a moulding with a piece of metal inside. Mouldings with metal inserts can be difficult to cut, but by using the Spacer HydroBlade cutting these is a breeze. Also, many encapsulated glasses have a very dense encapsulation material that is difficult to cut. To save unbroken glass these blades are designed to hold the blade below the moulding and prevent the blade from cutting into the encapsulation. A permanently attached, self-lubricating nylon spacer lets the blade move easily back and forth while holding the blade under the lower lip of the moulding or encapsulation. Made of a proprietary grade of stainless steel. Made in the USA. Learn More
  23. Equalizer HydroBlade

    Equalizer HydroBlade - EHS175

    $38.68

    Some vehicles have a moulding with a piece of metal inside. Mouldings with metal inserts can be difficult to cut, but by using the Spacer HydroBlade cutting these is a breeze. Also, many encapsulated glasses have a very dense encapsulation material that is difficult to cut. To save unbroken glass these blades are designed to hold the blade below the moulding and prevent the blade from cutting into the encapsulation. A permanently attached, self-lubricating nylon spacer lets the blade move easily back and forth while holding the blade under the lower lip of the moulding or encapsulation. Made of a proprietary grade of stainless steel. Made in the USA. Learn More
  24. Equalizer Piranha Blade 3"x14"
  25. BlackHawk™ 20-Volt Tool

    BlackHawk™ 20-Volt Tool

    $589.00

    BlackHawk™ has a heavy-duty, 20-Amp Learn More

25 Item(s)

per page

List  Grid 

Set Descending Direction

Glass Pro Supplies, Copyright 2017

 

 

 

Mobile Site | Back to Top